Home -

China Mobile 5G CPE + AC1200 Router Network Deployment Solutions

China Mobile 5G CPE + AC1200 Router Network Deployment Solutions

 

Design of 5G Wireless Broadband Access and Indoor Wi-Fi Coverage in Scenarios Without Fiber-to-the-Home

 

Table of Contents

01/

Background and Scope of the Proposal
Appropriate and Inappropriate Scenarios, Three Design Principles

02/

Overall Topology
Base Station-CPE-Router-Terminal Links and Cabling Types

03/

Two Operating Modes
Comparison of CPE Bridge Dial-up and CPE Routing AP

04/

Equipment and Key Parameters
Equipment List, CPE, and AC1200 Parameter Baseline

05/

Deployment Steps and Wireless Optimization
Implementation Processes and Wireless Parameters for the Two Modes

06/

Precautions, Acceptance, and Delivery
Risk List, Acceptance Criteria, Issue Investigation, and Documentation

 

Background of the Proposal

 

In scenarios without fiber optics, 5G access is the preferred option; however, high-concurrency and low-latency services are not covered by this solution.

Applicable Scenarios

  • Rural self-built homes and suburban courtyards without fiber-optic coverage
  • Short-term internet access for construction sites, temporary offices, trade shows, and similar locations
  • Shops, warehouses, and surveillance data transmission without in-home cabling
  • Coverage for rental properties and vacation rentals in underserved areas

Situations Where This Does Not Apply

  • Low-latency services such as esports and professional live streaming
  • Remote access relying on static public IP addresses and port forwarding
  • Long-term, high-volume downloads and backups
  • Venues with high concurrency (hundreds of users)

Design Principles

  • Separate responsibilities between the public network side and the internal network side to avoid double NAT.
  • Port throughput takes precedence over nominal wireless speeds; both ends must support Gigabit.
  • Plan the number of devices and service types based on on-site signal measurements.

 

Overall Topology

 

Base Station → CPE → AC1200 → Wired and Wireless Terminals

 

1

 

Solid lines represent wired links, and dashed lines represent wireless links; 5G access is wireless backhaul.

Link Description

  • The CPE connects to the 5G base station via SIM and converts the signal to Ethernet.
  • The CPE's LAN connects to the AC1200 via a Gigabit Ethernet cable.
  • Wired devices connect via Gigabit LAN; 5G and 2.4 GHz wireless connections are supported.
  • The CPE's built-in Wi-Fi must be turned off to avoid co-channel interference.
  • Mode A connects to WAN; Mode B connects to LAN, and DHCP must be disabled.

 

Operating Modes

 

The two operating modes are determined by the CPE's capabilities: Supports bridging-priority mode A

 

Comparison Items

Mode A: CPE Bridging + Routed Dial-up

Mode B: CPE Routing + Routing to AP

CPE Settings

Turn off DHCP, turn off built-in Wi-Fi, and enable bridge mode

Keep the router connected via dial-up and turn off the built-in Wi-Fi

How to Connect a Router

CPE LAN connected to router WAN

Connect the CPE's LAN port to the router's LAN port; do not connect it to the WAN port.

Router Settings

Obtain an IP address, enable DHCP, NAT, and the firewall

Disable DHCP; use as a wireless access point only

Number of NAT Layers

Layer 1: Port forwarding and remote access are supported

Two layers; remote access requires the CPE to enable DMZ

Ease of Management

Internal network policies are centralized on the router, making it easy to limit speeds and isolate networks.

Strategies are scattered; additional configuration is required on the CPE side.

Recommendation Level

When CPE supports bridging, it gives priority to

Common Practices for Customizing CPE

 

Equipment List

 

Three Key Criteria for Equipment Selection: Gigabit connectivity at both ends, CPE support for the required mode, and router support for AP mode

 

No.

Equipment and Materials

Key Specification Requirements

Quantity

1

China Mobile 5G CPE

Gigabit LAN, supports 5G SA/NSA, with external antenna support

1 unit

2

AC1200 Gigabit Router

All Gigabit ports, 2×2 dual-band, supports AP mode

1 unit

3

5G External Antenna (Optional)

Matching by CPE interface, gain 5–9 dBi

[ ] sets

4

Category 5e / Category 6 Network Cables

Cat 5e or higher, with a single run ≤ 30 meters

[ ] meters

5

Voltage-Regulated Power Strip or UPS

Allow a 30% margin on the rated power

1 set

6

Mounting Brackets and Accessories

Mounted by the window or high on the wall

[ ] sets

 

Parameter Baseline

 

Signal quality determines the upper limit of 5G; AC1200 performance determines wireless coverage within the local network

 

5G CPE Side

Parameters

Caliber

Network Standards

5G SA/NSA, backward compatible with 4G; SA offers lower latency

Operating Frequency Band

n41(2.6GHz),n78(3.5GHz)

Signal Evaluation

An RSRP of ≥ -85 dBm is optimal; if it is below -105 dBm, the location needs to be adjusted.

Signal-to-Noise Ratio

A SINR of ≥ 15 dB is optimal; below 5 dB, the data rate drops sharply.

AC1200 Router Side

Parameters

Caliber

Wireless Standards

802.11ac (Wi-Fi 5), compatible with n/b/g

Theoretical Rate

2.4 GHz 300 Mbps + 5 GHz 867 Mbps, for a total of AC1200

Bandwidth

2.4 GHz, 20/40 MHz; 5 GHz, up to 80 MHz; no 160 MHz

Encryption / Device Support

WPA2-PSK (AES); recommended for 15–20 devices

 

Deployment Steps

 

The two modes are selected based on CPE capabilities; the procedures and connection methods must not be mixed.

Mode A: CPE Bridging + Routed Dial-up

  • Insert the SIM card, power on the device, verify 5G registration, and record the RSRP/SINR/frequency band
  • Enable bridge mode on the CPE, and disable DHCP and the built-in Wi-Fi
  • Ethernet cable: CPE LAN → Router WAN
  • The router's WAN port obtains an IP address; enable DHCP and the firewall
  • Configure Wi-Fi: 2.4 GHz 20 MHz, 5 GHz 80 MHz, WPA2-AES
  • Enable guest network, speed limits, and whitelists/blacklists as needed

Mode B: CPE Routing + Routing to AP

  • Keep the CPE connected via dial-up and disable its built-in Wi-Fi.
  • Ethernet cable: CPE LAN → Router LAN (bypass the WAN port)
  • Disable DHCP on the router and configure non-conflicting IP addresses within the same subnet.
  • Ensure wireless parameters match those in Mode A.
  • For remote access, enable DMZ or port forwarding on the CPE.

 

Wireless Optimization

 

The goal of the parameter is to maintain stability within a limited frequency range, rather than to achieve peak performance.

 

Configuration Options

Recommended Values

Reason

2.4 GHz bandwidth

20MHz

In a congested environment, 40 MHz causes continuous co-channel interference

2.4 GHz Channel

Fixed 1 / 6 / 11

The three do not overlap; select the clearest channel at the site.

5G Bandwidth

80 MHz; reduce to 40 MHz when interference is heavy

Narrow Bandwidth for Stability

5G Channels

Priority: 36/40/44/48, 149/153/157/161

Avoid radar detection channels and reduce automatic frequency hopping

Encryption Method

WPA2-PSK(AES)

Ensure compatibility with older devices to prevent WPA3 authentication failures

Transmit Power

Don't set it to maximum; adjust it based on coverage.

High power increases background noise and degrades the edge experience

SSID Policy

Separate naming for 2.4G and 5G; dedicated SSID for IoT

Prevent the device from repeatedly switching between frequency bands

 

Key Points to Note

 

Most issues stem from site selection, wiring, and parameter settings; verify each item before delivery.

 

5G Signal and Locations

When the RSRP is below -105 dBm, the only options are to adjust the location or connect an external antenna; speed reductions during the evening rush hour caused by base station congestion are due to issues on the carrier's side and cannot be resolved by replacing equipment.

01

Ports and Cabling

Both the CPE and the router must be Gigabit-capable; Mode B must be configured as LAN-to-LAN; if mistakenly connected to the WAN, it will result in double NAT.

02

Wireless and Handsets

The CPE's built-in Wi-Fi must be turned off; a single AC1200 unit can reliably support 15–20 devices; if this limit is exceeded, additional access points should be added.

03

Plans and Data Allowances

Distinguish between general-purpose, dedicated, and IoT SIM cards, and verify speed-limiting and data-cap rules; data costs are higher than fiber optic service, so these SIM cards are not suitable for long-term, high-volume data usage.

04

Power Supply and Reliability

Install UPS units at critical locations; ensure CPE is well-ventilated and protected from direct sunlight; document the account number, parameters, and orientation of each location upon delivery.

05

 

Acceptance and Inspection

 

First, check the signal and registration; next, check the connection ports; finally, check the wireless settings and device compatibility.

 

Acceptance Criteria

Acceptance Criteria

Evaluation Criteria

Signal Quality

RSRP ≥ -95dBm,SINR ≥ 10dB

Port Negotiation

Both the CPE and the router negotiate Gigabit speeds.

Coverage Intensity

5G ≥ -65dBm,2.4G ≥ -70dBm

Latency and Packet Loss

Average <15 ms, packet loss ≤1%

Model Correctness

Consistent with the selected mode; no misconfiguration of double NAT

Handling Frequently Asked Questions

Phenomenon

Procedures

The speed test shows only 100 Mbps

Check the specifications of both ports, and replace them with a compatible Ethernet cable and RJ45 connector.

Remote Monitoring Is Unavailable

Switch to Mode A, or enable DMZ on the CPE.

Full signal strength but slow data speed

Turn off the CPE's Wi-Fi, set the 2.4 GHz band to a fixed 20 MHz channel, and change the channel.

Frequent Disconnections and Restarts

Improve power supply and ventilation, and reinsert the SIM card.

Multiple devices are lagging at the same time

Limit the number of connected devices and add more access points.

 

Deliverables

 

Clearly define the scope boundaries during the contract phase to avoid disputes during acceptance.

Scope Boundaries

  • Does not support low-latency gaming or live streaming services
  • Does not guarantee a fixed public IP address or stable port mapping
  • Not suitable for long-term, high-volume downloads or backups
  • High concurrency requires an enterprise-grade 5G gateway with a wired backhaul

List of Deliverables

  • Topology and Site Maps: Location, Orientation, and Terminal Distribution
  • 5G Signal Survey: RSRP, SINR, Frequency Bands, Time Slots
  • Equipment and Accounts: Model, SIM Card, Administrative Address and Password
  • Acceptance Test Records: Negotiation, Data Rate, Coverage, Latency, and Packet Loss

 

The lack of support for new features on the terminal side does not constitute a construction quality issue; commissioning and testing will be completed within the capabilities of existing equipment, and we assume no responsibility for any discrepancy in terminal capabilities.